Find Ni46 Strip, Ohmalloy1J46 Strip, Soft Magnetic Alloy Strip on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)
Home > Products > Soft Magnetic Alloy > 1j79 Strip 0.1*20mm Permalloy for Transformer Element

1j79 Strip 0.1*20mm Permalloy for Transformer Element

Basic Info

Model No.:  OhmAlloy-1J79

Product Description

Model NO.: OhmAlloy-1J79 Material: Fenico Alloy PCD: Feni Alloy Hole: 0 Condition: Soft Transport Package: Coil+ Waterproof Paper+ Wooden Case Origin: Shanghai, China Product Type: Strip Carbon Content: Low Carbon ET: 0 Surface: Bright Trademark: OhmAlloy-1J79 Specification: 0.1*20mm HS Code: 7220900000  OHMALLOY OhmAlloy-1J79  (Soft Magnetic Alloy)
(Common Name: Ni79Mo4, E11c, malloy, permalloy, 79HM) 
Ohmalloy-1J79 is a nickel-iron magnetic alloy, with about 80% nickel and 20% iron content. Invented in 1914 by physicist Gustav Elmen at Bell Telephone Laboratories, it is notable for its very high magnetic permeability, which makes it useful as a magnetic core material in electrical and electronic equipment, and also in magnetic shielding to block magnetic fields. Commercial permalloy alloys typically have relative permeability of around 100,000, compared to several thousand for ordinary steel.
In addition to high permeability, its other magnetic properties are low coercivity, near zero magnetostriction, and significant anisotropic magnetoresistance. The low magnetostriction is critical for industrial applications, allowing it to be used in thin films where variable stresses would otherwise cause a ruinously large variation in magnetic properties. Permalloy's electrical resistivity can vary as much as 5% depending on the strength and the direction of an applied magnetic field. Permalloys typically have the face centered cubic crystal structure with a lattice constant of approximately 0.355 nm in the vicinity of a nickel concentration of 80%. A disadvantage of permalloy is that it is not very ductile or workable, so applications requiring elaborate shapes, such as magnetic shields, are made of other high permeability alloys such as mu metal. Permalloy is used in transformer laminations and magnetic recording heads.
Ohmalloy-1J79 widely used in radio-electronic industry, precision instruments, remote control and automatic control system.
 
 Normal composition%
Ni 78.5~80.0 Fe Bal. Mn 0.6~1.1 Si 0.3~0.5
Mo 3.8~4.1 Cu ≤0.2        
C ≤0.03 P ≤0.02 S ≤0.02    
 Typical Mechanical properties
Yield strength Tensile Strength Elongation
Mpa Mpa %
980 1030 3~50
 Typical Physical properties
Density (g/cm3) 8.6
Electrical resistivity at 20ºC(Om*mm2/m) 0.55
Coefficient of linear expansion(20ºC~200ºC)X10-6/ºC 10.3~11.5
Saturation magnetostriction coefficient λθ/ 10-6 2.0
Curie point   Tc/ ºC 450

 
The magnetic properties of alloys with high permeability in weak fields
1J79 Initial permeability Maximum permeability Coercivity Saturation magnetic induction intensity
Сold-rolled strip/ sheet.
Thickness, mm
μ0.08/ (mH/m) μm/ (mH/m) Hc/ (A/m) BS/ T
0.01 mm 17.5 87.5 5.6  
 
 
 
 
 
 
 
 
 
0.75
0.1~0.19 mm 25.0 162.5 2.4
0.2~0.34 mm 28.0 225.0 1.6
0.35~1.0 mm 30.0 250.0 1.6
1.1~2.5 mm 27.5 225.0 1.6
2.6~3.0 mm 26.3 187.5 2.0
cold drawn wire  
0.1 mm 6.3 50 6.4
Bar  
8-100 mm 25 100 3.2
 
Mode of heat treatment  1J79
Annealing media Vacuum with a residual pressure not higher than 0.1Pa, hydrogen with a dew point of not higher than minus 40 ºC.
The heating temperature and rate 1100~1150ºC
Holding time 3~6
Cooling rate With 100 ~ 200 ºC/ h cooled to 600 ºC, rapidly cooled to 300ºC
 
 
Style of supply
Alloys Name Type Dimension  
OhmAlloy-1J79 Wire D= 0.1~8mm  
OhmAlloy-1J79 Strip W= 8~390mm T= 0.3mm
OhmAlloy-1J79 Foil W= 10~100mm T= 0.01~0.1
OhmAlloy-1J79 Bar Dia= 8~100mm L= 50~1000
 
Permalloy was initially developed in the early 20th century for inductive compensation of telegraph cables.When the first transatlantic submarine telegraph cables were laid in the 1860s, it was found that the long conductors caused distortion which reduced the maximum signalling speed to only 10-12 words per minute. The right conditions for transmitting signals through cables without distortion were first worked out mathematically in 1885 by Oliver Heaviside. It was proposed by Carl Emil Krarup in 1902 in Denmark that the cable could be compensated by wrapping it with iron wire, increasing the inductance and making it a loaded line to reduce distortion. However, iron did not have high enough permeability to compensate a transatlantic-length cable. After a prolonged search, permalloy was discovered in 1914 by Gustav Elmen of Bell Laboratories, who found it had higher permeability than silicon steel. Later, in 1923, he found its permeability could be greatly enhanced by heat treatment. A wrapping of permalloy tape could reportedly increase the signalling speed of a telegraph cable fourfold.
 
This method of cable compensation declined in the 1930s, but by World War 2 many other uses for Permalloy were found in the electronics industry.

Dear Customers if you have any questions about our prodution, please give us email. We always glad to build better future with you!

Contact us if you need more details on Permalloy Strip. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Ohmalloy-1j79 Strip、Transformer Material. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Soft Magnetic Alloy

Email to this supplier
  • *Subject:
  • To:

  • *Messages:
    Your message must be between 20-8000 characters